EverFocus Speed Dome EPTZ1000 Bedienungsanleitung

Speed Dome EPTZ1000 USER MANUAL Date: Mar 2009

1-9SW1ON12345678CPUON12345678SW2ID1ID2ID3ID4ID5ID6ID7ID8ProtocolBAUD 1.4. EPTZ1000Connection Alarm 1Alarm 4Alarm 3Alarm 2GROUNDRS485 Tx(+)RS485 Tx(-

1-101.5. EPTZ1000 Quick Operation Guide EPTZ1000and EKB500 (Keyboard) can work together by using factory default setting. You just need to connec

2-112. EPTZ1000INSTALLATION 2.1. Packing List There are 3 boxes that are housing, bulb and mechanical part with a camera module, one wall mount brack

2-12 - Video Cable A BNC cable is used for connecting a speed dome to a DVR or a monitor. An amplifier may be needed if the video cable is too long.

2-132.3.1. Address Setting The address code of the EPTZ1000should be set to correspond properly with a control device to control multiple dome camera

2-14ON12345678Switch Address1ON123456782ON123456783ON123456784ON123456785ON123456786ON123456787ON123456788ON123456789ON1234567810ON1234567811ON123456

2-15ON12345678Switch Address129ON12345678130ON12345678131ON12345678132ON12345678133ON12345678134ON12345678135ON12345678136ON12345678137ON12345678138O

2-162.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits of the SW2 are used to set communication protocol. The factory default protocol

2-172.3.4. Video Format Setting The 6th bits of the SW2 on the PCB board are used to set the video format. The default video format depends on the f

2-182.4. Rack and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and shoul

1-1Table of Contents 1. EPTZ1000OVERVIEW ... 1-31.1. Introduction ...

2-192. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket. 3. Take off the housing from

2-205. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwi

2-21 Notice: In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb. 7. Turn on the power, and start

2-222.5. Separately Sold Accessories 2.5.1. Pole mount The pole mount is used for installing a speed dome on the ceiling indoors or outdoors. The

3-233. EPTZ1000CAMERA SETUP MENU In this section, setup and operation guide of EPTZ1000will be introduced. There are 25 items of the setting menu. H

3-243.1.1. Camera Setup Menu Press MENU to enter camera setup menu. Press Shift + Joystick up/down to change subentries, and right/left to change t

3-256. S.SHUTTER : (this function is only available for EPTZ1000) OFF: Disable auto slow shutter. AUTO: Auto Slow electrical shutter. In order to enh

3-2612. AUTO FLIP： Flip the camera when it tilts to the 90° end. ON: Enable auto flip. OFF: Disable auto flip. 13. ALM-IN1： The status of input al

3-27 OFF: Disable alarm input. 17. ALM-IN PRIO： The priority of alarms. 1234: The alarm priority is 1>2>3>4. 2341: The alarm priority

3-28For Tour setting: Shift joystick to right and left (< >) for changing Set Numeral (T01A~T16A), then press “Enter” to confirm. Shift joystic

1-22.5.3. Corner mount ... 2-222.5.4. Multi-Function Keyboard Contro

3-29Select this item, and then press “Enter” to load default setting. Press “Clr” + “Menu” whenever you want to quit menu setting. 25. EXIT : To exi

4-304. EPTZ1000FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Cou

4-31to enter 360° auto pan speed (1~239). The camera will turn 360° automatically, but not tilt. 4.3. Position Setting ¾ Focus on a preset position

4-32Dwell time: default is 2 sec; It can be changed by EVF Keyboard Set + A.Pan setting dwell time of A pos or B pos. 99 => Auto scan (360 degree)

4-33¾ One-way tour Mode: Press Tour to enter the tour mode. The system will ask you to enter the tour number you would like to run, and starts the t

4-34If you set the position number to 99, the dome will do a 360 degree auto scan or AB two point pan if limit is ON. If you set the position number

4-35RELAYJP6JP4JP3 JP1JP5Video +Video -RS485 +RS485 -AC24AC24JP51 ~ 9APPENDIX A: The Alarm I/O Connection There are 4 alarm inputs and 1 alar

4-36 EverFocus Electronics Corp. P/N: MW01G0040B Ver. C Your EverFocus product is designed and manufactured with high quality m

1-31. EPTZ1000OVERVIEW 1.1. Introduction EPTZ1000, an intelligent high-speed dome camera is ready to secure your property with its omni-directional a

1-4 All of the features make the intelligent high-speed dome camera works for a wide range and demanding application such as banks, airports, station

1-51.2. Specifications Pickup Device 1/4'' SONY Type EXview HAD CCD Video Format NTSC or PAL Scanning System NTSC: 525 TV lines, 60 fiel

1-6Preset Positions 192 positions Running to Position Speed 1－239 grade available,0.1º/s - 360º/s Dwell Time at Preset Position 1~239 second availab

1-7 1.3. Feature 1.3.1. Hardware Overview EPTZ1000 Wall Mount BracketHousingInner HousingM5 Bolt (Hex) x3M3 Bolt x3BNC CablePower CableRS485 CableC

1-81.3.2. Base Board The base board that is on the bottom of the housing connects to power cable, video cable, control cable, alarm cable, fan and h