EverFocus EPTZ Series Bedienungsanleitung

Speed Dome EPTZ3600/EPTZ3600I USER MANUAL Date: Oct. 2008

10 1.3.2. EPTZ3600/EPTZ3600I Base Board The base board that is inside the top housing connects to power cable, video cable, control cable, alarm cab

11 Pin # Function 1 ALM_NO_B (Alarm Output Normal Open B) 2 ALM_COM_B (Alarm Output Common B) 3 ALM_NC_B (Alarm Output Norm

121.4. EPTZ3600/EPTZ3600I Quick Operation Guide (Work with EKB500) EPTZ3600/EPTZ3600I and EKB500 (Keyboard) can work together by using factory defaul

132. EPTZ3600/EPTZ3600I INSTALLATION 2.1. Packing List There are 3 boxes that are camera main body with a camera module, top housing with a base boar

142.2. Cable Needed Power Cable An adapter with 24VAC/3.5A output provides the power to the EPTZ3600/EPTZ3600I. An extension power line may be nee

152.3. Initial Setup Initial setup includes dome address, communication protocol, transmission speed, and terminal resistance settings. All of the se

16 ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ID address Protocol/Baud rate/ Terminal resistance

17ON12345678Switch Address1ON123456782ON123456783ON123456784ON123456785ON123456786ON123456787ON123456788ON123456789ON1234567810ON1234567811ON12345678

18ON12345678Switch Address129ON12345678130ON12345678131ON12345678132ON12345678133ON12345678134ON12345678135ON12345678136ON12345678137ON12345678138ON1

192.3.2. Communication Protocol Setting The 1st, 2nd and 3rd bits are used to set communication protocol. The factory default protocol is EVF. N

2Table of Contents 1. EPTZ3600/EPTZ3600I OVERVIEW ... 5 1.1. Introduction ...

202.4. Bracket and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and shoul

21Pull here to open 2.4.2. EPTZ3600 Dome Camera Installation Note: Installation location that is a wall, a pole or a ceiling needs to support ab

22Pull open this switch 2. Apply the adhesive stripe at back of desiccant pack to the inner side of the top housing. There are totally 3 desiccant p

234. Connect the cable you detached from base board to the RS485 cable, Power cable and video cable you tread from the wall or ceiling. RS485 cable h

246. Thread the cable through the bracket. 7. Screw the top housing to bracket by using a hexagon wrench.

258. Screw in 4 long screws to fix the bracket to bracket base. 9. Pull the hole of base board to open it again. Connect the power and RS4

2610. There is a rope pendant from the top housing, this is used to support main body. The steps of how to apply the rope: a. Locate the hook first.

27 c. Done!

2811. Hold and push the main body toward the bracket until it is firmly fixed to the bracket. To release it, press orange buttons at both sides of th

29 Note 1: In order to protect the bubble from dirt and scrape, please put on the gloves before installing the bubble. Note 2: The camera

33.2.1. EXPOSURE ... 33 3.2.2. FOCUS MODE ...

302.5. Accessories 2.5.1. EPTZ-CPMA: Ceiling Pendant Mount Adapter The ceiling pendant mount adapter is used for installing a speed dome on

312.5.3. EPTZ- CMA: Corner Mount Adapter The corner mount are used for installing a wall mount bracket to a 270° corner of walls indoors or outdoo

323. EPTZ3600/EPTZ3600I CAMERA SETUP MENU In this section, setup and operation guide of EPTZ3600/EPTZ3600I will be introduced. There are 9 items of

333.2. VIDEO SETTINGS In main menu, turn joystick Up / Down to select VIDEO SETTINGS. Turn joystick Left / Right to enter VIDEO SETTINGS sub-menu (se

34There are 5 options in Exposure: EL. SHUTTER, SLOW SHUTTER, IRIS MODE, and AE SPEED. EL.SHUTTER: Select electronic shutter mode from the options o

35 AE SPEED: if you select AUTO in slow shutter, you can set exposure time (move the cursor between 0~6) EXIT: Select Exit to save settings and exit

36AUTO: this mode computed the white balance value output using color information from the entire screen. It outputs the proper value using the color

373.2.7. COLOR: In Color, we define color of the image. Select from ON and OFF. ON: Color image OFF: B/W image 3.2.8. NEGATIVE In Negative mode, it

383.3. POSITIONS In main menu, turn joystick Up or Down to select POSITION option. Press Enter key or turn joystick Left / Right to enter POSITION su

39 (diagram 3.6) POSITION: Select from SET and CLEAR. SET: Select SET and press Enter key of keyboard, you will be entered to a sub-menu. Turn the

43.6. ALARM ... 55 3.6.1. ALARM INPUTS ...

40SPEED: Select the speed for the preset position. The value is from 1 to 255 and 255 is the highest speed. DWELL TIME (S): Select the dwell time

413.4. OSD/AREAS In main menu, turn joystick Up or Down to select OSD/AREAS. Turn joystick Left or Right to enter OSD/AREAS sub-menu (see diagram 3.8

42In zone menu, you can set a zone and name it, when the speed dome turns to the zone you set, it will display zone name on the screen (only if “OSD/

43Turn joystick Right/Left to highlight the zone you have set and turn the joystick Up/Down to select another zone number. If you wish to clear the z

44 4. Go to “DEFAULT NORTH” and press Enter key to set the north position as default north position. (see diagram 3.14) (diagram 3.14) 5. Go to R

451. SHOW OSD ON: show OSD of Camera Title, Directions, Zones, Preset Title, Motion, Zoom, Fan and Camera Status. OFF: do not show OSD. 2 SEC: show O

46NO: do not show zoom multiple. 7. FAN YES: show fan indication when fan is enabled. NO: do not show fan indication. 8. MOTION YES: show motion me

47(diagram 3.16) 3.5.1. AUTOPAN Press Enter key of keyboard or turn joystick Left/Right to enter AUTOPAN sub-menu (see diagram 3.17) (diagram 3.17)

48Select speed from 1~255 and 255 is the highest speed. c. DWELL TIME L (S) Select dwell time of the left position from 1~99 seconds. d. DWELL TIME R

49(diagram 3.19) g. DEFAULT ON: all settings in AUTOPAN menu will be returned to default values. OFF: the setting in AUTOPAN menu is not default

51. EPTZ3600/EPTZ3600I OVERVIEW 1.1. Introduction EPTZ3600 series has 2 types, EPTZ3600 is outdoor type whereas EPTZ3600I is indoor type, using high

50(diagram 3.20) a. Tour NO.: Turn the joystick Left/Right to select tour number first b. PRE: Turn the joystick Left/Right to select preset posit

513.5.3. PATTERN Press Enter key of keyboard to enter PATTERN sub-menu (see diagram 3.21) (diagram 3.21) a. Turn the joystick Up or Down to select

52of pattern you set. e. When you return to PATTERN SETUP menu, turn the joystick Left/Right to PLAY. Press Enter key of keyboard. The camera star

53 (diagram 3.24) 3.5.5. RESUME TO Turn the joystick Left/Right to select the mode to resume to. It is selectable from PREV MODE, POS.1 (H), TOUR1,

543.5.6. POWER UP FUNC Turn the joystick Left or Right to select the mode to return to when power failure occurs. It is selectable from PREV MODE, P

553.5.8. EXIT Exit from the current menu. 3.6. ALARM In main menu, turn joystick Up or Down to select ALARM. Turn joystick Left or Right to enter A

56NIGHT NO: Set camera at night mode with normal open alarm input. When there is event triggered, the camera will be changed to day mode. OFF: Dis

57d. DURATION: Duration of alarm input. TIMEOUT: Turn the joystick Left or Right to select on TIMEOUT and press Enter key to select time-out. Time-o

583.6.2. ALARM OUTPUTS Press Enter key of keyboard to enter ALARM OUTPUTS sub-menu. (see diagram 3.30) (diagram 3.30) a. OUTPUT NUM: Select Output

59Select NO to disable this function. i. RETURN: RETURN to the previous menu. 3.6.3. MOTION DETECT Press Enter key of keyboard to enter MOTION DE

6¾ 192 preset positions are available. ¾ 16 cruise tours can be set, and each tour contains up to 16 positions. ¾ Up to 256 speed domes can be sup

60is represented by pink, Motion 2 by blue, Motion 3 by green and Motion 4 by yellow. Press IRIS+ key to save setting and return to previous menu. Pr

613.7. PRIVATE ZONES In main menu, turn joystick Up/Down to select PRIVATE ZONES masking. Turn joystick Left/Right to enter PRIVATE ZONE sub-menu (se

62 c. Select the area to be covered first. Turn joystick Left/Right to adjust width of the private zone area. Turn joystick Up or Down to adjust hei

633.8. SYSTEM In main menu, turn joystick Up/Down to select SYSTEM. Turn joystick Left/Right to enter SYSTEM sub-menu (see diagram 3.36) (diagram 3.3

64-PASSWORD ACTIVE: Select YES to activate password mode. Select NO to disable password mode. -ENTER PASSWORD: Enter the password -VERIFY PASSWORD:

65e. PRESET-CNT: Preset counter. This counter counts the preset movement, and 1 is counted when the speed dome runs to preset position. f. X-CONT: X

664. EPTZ3600/3600I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwis

674.3. Position Setting ¾ Focus on a preset position: Press the number key, and then press Position to focus on the number of preset position; or yo

6899 => Auto scan (360 degree) Default speed is 32. It can be changed by EVF Keyboard (Shift + A.Pan setting speed). We can even set camera’s ICR

69Preset a one-way tour: Press Set + Tour to preset a one-way tour. The system will ask you to enter preset position numbers (The positions need to b

71.2. Specifications Product Model EPTZ3600 (outdoor) EPTZ3600I (indoor) Pickup Device SONY 1/4” EX-view HAD CCD Video Format NTSC or PAL Scanni

70¾ Delete an alarm link: Press Clr + F1 to delete a link of alarm to position/tour. Note 1: After alarm output signal is terminated, the spee

71 P/N: MW01G02500 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan T

8Horizontal Rotation Speed 0.01°/s－360°/s (1-255 grade shift gears) Horizontal Rotation Range 360° unlimited rotation Tilt Rotation Range 180° pend

91.3. Feature 1.3.1. Profile of EPTZ3600/EPTZ3600I Wall Mount Bracket Sun shield (optional) Bubble Camera main body Top housing Camera module Oute