ES0802-41 8-port 10/100/1000M PoE+ Web Smart Gigabit Ethernet Switch
PoE Switch 5 Rear Panel The 3-pronged power plug is placed at the rear panel of the switch right side
PoE Switch 6 3. Software Description This part instructs user how to set up and manage the switch thro
PoE Switch 7 Figure 1-2 3.1 Configuration System System Configuration This page shows system configu
PoE Switch 8 Figure 1-3 MAC Address: Displays the unique hardware address assigned by manufacturer
PoE Switch 9 manage the switch. By default, all ports on the switch are members of VLAN 1. However, if
PoE Switch 10 Figure 1-4-1 Figure 1-4-2 VLAN A Virtual LAN (VLAN) is a logical network grouping that
PoE Switch 11 same switch physically. Port Segmentation (VLAN) Configuration VLAN ID: ID of confi
PoE Switch 12 The 802.1Q Per Port Configuration page allows you to change the VLAN parameters for indi
PoE Switch 13 effect on ports that have Packet Type set to “Tagged Only.” (Default PVID: 1) It is not
PoE Switch 14 LACP Port Configuration Port: The port number. Enabled: Enables LACP on the associat
EVERFOCUS ELECTRONICS CORPORATION PoE Switch User’s Manual 2013 EverFocus Electronics Corp www.everfoc
PoE Switch 15 changing states (i.e., discarding to learning to forwarding). Number between 4 – 30 (def
PoE Switch 16 Figure 1-8-2 Figure 1-8-3 Figure 1-8-4
PoE Switch 17 IGMP Snooping IGMP Snooping is the process of listening to IGMP network traffic. IGMP
PoE Switch 18 on one switch port (or an entire VLAN) to a network monitoring connection on another swi
PoE Switch 19 Figure 1-10-2 Quality of Service (QoS) In QoS Mode, select QoS Disabled, 802.1p, or DSC
PoE Switch 20 Figure 1-11-1 QoS Mode: QoS Disabled When the QoS Mode is set to QoS Disabled, the foll
PoE Switch 21 Figure 1-11-3 Figure 1-11-4 QoS Mode: DSCP DSCP: Packets are prioritized using the DSC
PoE Switch 22 DSCP Configuration table to a common priority queue. Use Custom if you want to set each
PoE Switch 23 Remote access and monitor the attached PD (Powered Device) status by using Enable/Disabl
PoE Switch 24 Figure 1-13-1 Enable Rate Limit: Click the check box to enable storm control. Rat
Safety Precautions FCC Warning This Equipment has been tested and found to comply with the limits for a C
PoE Switch 25 Figure 2-1 Detailed Statics Figure 2-2 LACP Status LACP Aggregation Overview Figure 2
PoE Switch 26 Port: The port number. Port Active: Shows if the port is a member of an active LACP
PoE Switch 27 because every device must receive information about topology changes before it starts to
PoE Switch 28 IGMP Status IGMP Status IGMP Status shows the IGMP Snooping statistics for the whole swi
PoE Switch 29 Figure 2-6-1 Figure 2-6-2 Figure 2-6-3
PoE Switch 30 Figure 2-6-4 Ping This command sends ICMP echo request packets to another node on the n
PoE Switch 31 Figure 2-7-1 Figure 2-7-2
PoE Switch 32 Figure 2-7-3 3.3 Maintenance Warm Restart Press Yes button to restart the switch, the r
PoE Switch 33 Software upload Select “Upgrade Firmware” from the Tools drop-down list then click on t
PoE Switch 34 Figure 3-5 3.4 Reset button for the factory default setting Please take the following
Table of Contents Table of Contents ...
EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiw
Ping ...
PoE Switch 1 1. Introduction 1.1 Product Overview This switch is a Web Smart Switch equipped with
PoE Switch 2 Statistics Overview Detailed Statistics LACP Status RSTP Status IGMP Status VeriPHY Ping
PoE Switch 3 Port 1~8: Link/ Act, 1000M. Port 1~8: PoE Per Unit: Power Power Consumption: 130 Watts
PoE Switch 4 2. Hardware Description This part primarily presents hardware of this switch, physical
Kommentare zu diesen Handbüchern